Search
`
November 1, 2024

PJM Responds to Pa. Concerns About Baseload Plants

By Rory D. Sweeney

PJM’s Board of Managers last week assured Pennsylvania legislators that the state has ample power generation for its needs and cautioned that fuel diversity will not ensure reliability.

The RTO was responding to a Feb. 9 letter from the state legislature’s Nuclear Energy Caucus with its own letter that seemed intended to assuage lawmakers’ fears about of blackouts and grid interruptions caused by inadequate resources. While the caucus’s message referred only to “baseload” units, it did voice support for several FERC and PJM initiatives that would benefit coal and nuclear plants.

Peach Bottom Nuclear Generating Station in 1974

“We are losing confidence in the ability of wholesale electric markets to ensure Pennsylvania maintains a diverse supply of baseload generation resources that ensure stable prices for our citizens and a reliable and resilient electrical grid,” the caucus wrote. “Pennsylvania’s baseload power plants continue to face the risk of premature retirement, and we do not see expeditious and sufficient action being taken by PJM or the Federal Energy Regulatory Commission to correct the market flaws at the heart of this problem — flaws that PJM itself acknowledges.”

PJM’s Independent Market Monitor noted last week in its 2017 State of the Market report that just 52% of coal-fired plants in the RTO recovered their avoidable costs in 2017. All of Pennsylvania’s five nuclear facilities made enough money to cover their costs last year, although none did in 2016, the report showed. Three Mile Island has seen negative revenues since 2015 and will continue to through 2020 unless market changes occur, while the other four will remain profitable through that year. (See IMM Report Says PJM Prices Sufficient.)

Adequacy Assured

PJM CEO Andy Ott penned the response to the caucus, which defended the RTO’s operations. Ott noted that Pennsylvania has built more than 12,000 MW of new generation over the 20 years that the RTO has managed its grid, calling it “a direct result of the investment signals sent by the PJM wholesale market.”

In the past six years, Pennsylvania has produced between 18 and 27% more energy than it needed, equating to about 6,500 MW of generation, or nearly two-thirds of the Keystone State’s nuclear fleet, Ott said.

While the caucus’s letter never mentioned costs, Ott remained focused on them, noting that “PJM markets have yielded reliability at the lowest cost for Pennsylvania.”

Diversity Necessary?

The caucus said its “concern has only been heightened by” the cold snap in January known as the “bomb cyclone.” (See PJM: Cold Snap Uplift Shows Need for Pricing Changes.)

“The dramatic increase in wholesale power prices during that period highlight the risk of overreliance on any single fuel source, a risk we believe PJM can and should avoid by swiftly enacting reforms,” the legislators wrote. “We believe that [PJM’s price-formation proposal] is an important first step in recognizing the benefits of fuel diversity within this market, and one that will help keep our grid — and power prices — stable for many years to come.”

Ott noted in his response that both the RTO and Pennsylvania are more fuel-diverse today than ever, but downplayed the significance of that fact.

“Fuel diversity, however, is not a metric with which PJM can measure reliability,” he said. “Instead, fuel security — the certainty of fuel availability for power production — affects reliability.”

Market Changes

The caucus supported PJM’s efforts to revise its energy price-formation methodology, calling the current process “a flaw in its market rules that unfairly disadvantages certain low-cost baseload generation resources” by not allowing them to set clearing prices. As a result, “market prices are artificially low and do not reflect the true cost of meeting customer demand.” It gave PJM “credit” for developing “a potential solution.”

The RTO’s solution is a controversial plan to allow large, inflexible units like coal and nuclear to set clearing prices. Currently, those plants’ bids are often among the highest of dispatched units, but only “flexible” units that can regulate their output in response to price signals are allowed to set prices. The inflexible units receive subsequent “uplift” payments to cover their operating costs. In PJM’s plan, those units would set price and the flexible units would be paid additional revenue to back down their output to avoid oversupply.

Critics of the plan argue that plants that don’t receive enough revenue in the competitive market should take that as a signal to shut down, not change the rules.

The caucus called the proposal “an important first step” but said it “will not fully correct the existing market flaws nor fully provide the compensation necessary to maintain baseload resources.” Still, a failure to implement the plan “will continue to inequitably exacerbate the financial challenges” those units face, the lawmakers said.

While Ott did not specifically address PJM’s price-formation proposal, he acknowledged “there is room for markets to more sharply define power grid requirements.”

“Efforts are underway to improve wholesale market price efficiency for all the resources that rely upon the wholesale market to compensate them for their services, and appropriately to provide transparent investment signals,” he assured the legislators.

Ott has previously said that the proposal would result in increased energy prices but decreased uplift and capacity prices. (See “PJM Pushes Price Formation Plan,” FERC, RTOs: Grid Performed Better in Jan. Cold Snap vs. 2014.)

Monitor’s Position

In his market report, Monitor Joe Bowring said the changes were not based on market flaws. Nearly 79% of the $24.7 million in uplift costs from day-ahead operating reserve differences were paid to coal units in 2017, but not because of market design issues, he said.

“That actually has to do with some very specific circumstances about coal units that have nothing to do with convexity and non-convexity and would not be affected by PJM’s price-formation proposal,” Bowring said.

FERC Resilience

The caucus also applauded PJM’s proposal as “entirely consistent” with the state legislature’s resolution in October calling on FERC to address the U.S. Department of Energy’s Notice of Proposed Rulemaking to financially support baseload generation. FERC denied the NOPR request in January but opened a docket to investigate concerns about the resilience of the nation’s energy grid.

The caucus endorsed the new docket as “an early step” and said it plans to press for any recommended changes that emerge from it.

“We are encouraged that FERC valued our concerns,” the caucus wrote. “You should know that as elected lawmakers ultimately responsible for our commonwealth’s energy policy, we will engage in the discussion and strongly support urgent implementation of critical findings.”

Stakeholders Mull BTM Impact on MISO Tx Planning

By Amanda Durish Cook

CARMEL, Ind. — After six months of little progress, stakeholders are now asking MISO to consider changing its billing practices to reflect how behind-the-meter resources use the transmission system.

But the RTO says it’s still collecting stakeholder input before it develops an official stance on multiple BTM measures.

behind-the-meter transmission planning miso
Webb | © RTO Insider

“In large part, we’re still in listening mode here,” MISO Director of Planning Jeff Webb said at a March 14 Planning Advisory Committee meeting.

The RTO is still working with stakeholders to determine whether it should account for net or gross BTM load when it assesses network integration transmission service.

“I think that’s the debate here: whether behind-the-meter uses the transmission system for load, uses it sufficiently enough or uses it on peak,” Webb said. “Under what circumstances are costs incurred [from load typically served by BTM generation] when building the transmission system?”

The RTO must also settle on planning study assumptions for both registered and unregistered BTM generation and determine whether BTM retirements should be subject to a formal Attachment Y notice and subsequent reliability studies.

Last year, WEC Energy Group proposed that all resources be required to register with MISO as a network resource before being authorized to fulfill capacity obligations. That proposal aligns with an existing RTO plan to implement a one-time deliverability test for BTM generators that could trigger a requirement to acquire network service in an upcoming capacity auction. (See WEC Takes Stab at MISO Behind-the-Meter Definition.)

behind-the-meter transmission planning miso BTM
The MISO Planning Advisory Committee met on March 14 | © RTO Insider

Webb said MISO will continue to discuss how to plan for BTM generation at the PAC’s April meeting and that the conversation would likely extend until the end of the year.

“We’ll make some sort of strawman proposal and let people beat up on that for awhile until we get something,” Webb said. “Let’s keep the dialogue going here.”

Stakeholders: Tx Charge Rewrite?

The question of how to bill BTM generation for transmission use sparked a larger conversation on revising transmission use charges in the face changing load shapes in MISO.

Veriquest Group’s David Harlan said MISO is headed for a future of more complex and “spiky” load shapes attributable in part to BTM generation, possibly requiring the RTO to reassess how it bills for transmission use.

“In the past we’ve expected load shapes to be fairly predictable and planned around peak. I think what we’re increasingly seeing is that when you connect to the transmission or distribution system, there’s an option value. You can either inject or withdraw. What’s the proper way of accounting for that option right?”

Wisconsin Public Service’s Chris Plante said his company has also been discussing a more nuanced approach to transmission billing.

“I think more and more we’re not just building transmission for the peak, but for energy withdrawal,” Plante said.

Representing Illinois Industrial Energy Consumers, Jim Dauphinais said he’d like to see the transmission charge issue contained within the broader BTM subject, noting that MISO’s Regional Expansion Criteria and Benefits Working Group is responsible for proposing transmission cost-sharing policies.

Webb said he supported limiting the issue to how MISO plans for and bills for BTM generation ― for now.

“I think maybe we bite off what we can here,” Webb said. “I think we’re in a — every generation says this — but we’re in a transitional period. There’s growing uncertainty about the load that we plan for.”

CAISO Day-ahead Could be Tailored for West

By Jason Fordney

LOS ANGELES — CAISO’s proposal to extend its day-ahead market across the Western Energy Imbalance Market (EIM) could be tailored to uniquely fit a region historically resistant to organized markets, a key participant in the roll-out of the EIM said.

Edmonds | © RTO Insider

The ISO’s Extended Day-Ahead Market (EDAM) proposal could also be done without the political and economic entanglements involved with an RTO, Portland General Electric Director of Transmission Services Sarah Edmonds said during a March 9 public meeting of the EIM Regional Issues Forum (RIF). It could strike a balance between an ISO transmission access charge and a full RTO construct, she said.

“It is possible that with EDAM, a different construct will be born,” Edmonds said, adding that her comments reflected her own opinions, but they are “illustrative of the kinds of questions and issues the EIM community would be looking at” to determine their interest in day-ahead market participation.

In her previous job as general counsel for PacifiCorp, Edmonds served on the EIM’s Transitional Committee, which advised CAISO’s Board of Governors on the development of the market’s governance structure.

Sarah Edmonds Day-ahead market western RTO CAISO
The Western EIM Regional Issues Forum met last week in Los Angeles | © RTO Insider

A “winning feature” of the EIM has been that participating balancing authority areas retain their responsibilities and control, Edmonds said, pointing also to the benefits of voluntary participation and no exit fee. But as they explore EDAM, industry participants will need to address the many issues around how excess transmission capacity is shared. (See CAISO Plan Extends Day-Ahead Market to EIM.)

As for an RTO, the issue of governance — which was still being debated in the California legislature when last year’s regionalization effort stalled — is “center stage,” Edmonds said. Lawmakers are working on new legislation this session. (See Calif. Lawmakers Relaunch CAISO Regionalization.)

Governance is important because “the power of who gets to decide what issue is a big deal when you are talking about what comes with a full regional ISO,” Edmonds said.

Industry stakeholders still have many questions about transmission development and costs in a Western RTO because of the longer transmission lines, distance between loads and other planning considerations such as increased adoptions of distributed energy. Other complications include state roles in resource adequacy planning, transmission access charges and a regional transmission planning framework, she said.

“These issues really come up and are of particular concern in a regional ISO context,” she said, adding that there is also a “deeply ingrained culture of self-determination in the West.”

‘A Lot of Work’

Kathy Anderson, Idaho Power systems operations leader, told the RIF that her utility has been working on EIM implementation for two years and is due to go fully live on April 4, having shifted the date from April 1 because of the Easter holiday. One of the uses of the market will be to market renewable energy from qualifying facilities under the Public Utilities Regulatory Policies Act.

Sarah Edmonds Day-ahead market western RTO
Anderson | © RTO Insider

Anderson told the forum that the two-year process to integrate into the EIM has not been easy.

“I don’t think I really appreciated it until I was right in the middle of it. It was a lot of work,” Anderson said. “There were very few places in the company that we didn’t touch with this.”

The company employed three full-time external contractors and hired 6 employees to work directly on the EIM. It also required new software applications and outage management system.

Idaho Power and Canadian marketer Powerex have been in parallel operations with the EIM, in preparation for going live early next month. (See EIM Participants Seek Resource Test Tweaks.)

Updated: SPP Begins Work of Integrating Mountain West

By Tom Kleckner

SPP’s Board of Directors and Members Committee on Tuesday approved a set of conditions that will guide Mountain West Transmission Group’s pending membership into the RTO.

SPP said the board’s endorsement during a special meeting in Dallas represents “a vote of confidence in the value of Mountain West’s membership and the benefits it will bring to SPP’s existing members, the Mountain West entities” and their customers.

SPP Mountain West Transmission Group
Platt River Power Authority’s Andy Butcher shares details on his company with SPP stakeholders in July | © RTO Insider

COO Carl Monroe, who has been leading the RTO’s team during the negotiations, told RTO Insider he has been pleased with the work so far.

“We have been able to alleviate some of [Mountain West’s] concerns with joining SPP,” Monroe said Wednesday. “We’ve been able to work together and move forward. We’re pleased to come to this point, where we have general agreement of the things that are required to have Mountain West join SPP.”

The board approved 18 policy statements and directed staff and stakeholders to begin revising SPP’s Tariff, bylaws, membership agreement and other governing documents. The RTO’s Corporate Governance Committee and working groups will coordinate the work through the normal stakeholder process.

Changes to SPP’s Governing Documents Tariff will be presented for approval by stakeholder groups prior to going to the Members Committee and board.

The policies govern the terms of SPP membership, governance, the cost to operate the four DC ties in the SPP footprint, transmission planning and resource adequacy, and rates and revenue. SPP’s Regional State Committee would be expanded to include state commissioners from the Mountain West region.

SPP has scheduled a webinar on March 22 to provide further detail on the policies.

SPP and Mountain West members have been meeting behind closed doors since October to discuss the move. Monroe told stakeholders in January that a small negotiating team had been working to resolve a subset of “real contentious” issues. The Mountain West entities have suggested several governance changes important to their side of the footprint. (See SPP, Mountain West Resolving ‘Contentious’ Issues.)

SPP Mountain West Transmission Group
SPP’s Carl Monroe (l-r), Colorado Commissioner Frances Koncilja and Peak Reliability’s Marie Jordan during a June meeting in Denver | © RTO Insider

Mountain West has said studies have shown participating in SPP’s markets and efficiently using the DC ties between the two footprints would yield annual savings of $80 million to $154 million for its members. The entities also expect to realize additional benefits from regional transmission planning and SPP’s other services.

SPP has estimated its current members could receive more than $500 million in total net benefits over the first 10 years of Mountain West’s membership through reduced administrative costs because of a larger customer rate base, adjusted production cost savings from east-west energy exchanges and capacity cost savings from increased load diversity.

The RTO projects it will take about two years to fully integrate the Mountain West entities as members, but it plans to begin reliability coordination services in late 2019.

SPP currently serves a 546,000-square-mile, 14-state region. Mountain West’s membership would add 165,000 square miles, 16,000 miles of transmission lines, 21 GW of generating capacity and parts of three more states (Arizona, Colorado and Utah) to the RTO’s footprint.

Mountain West, which primarily services Colorado, Wyoming and Nebraska, began discussing RTO membership in 2013. It announced in January 2017 it was pursuing membership in SPP, and discussions entered a public phase in October. (See SPP, Mountain West Integration Work Goes Public.)

Emissions and Dispatch Top Talk at NY Task Force

By Michael Kuser

New York stakeholders on Monday wrestled with the complex issue of how to evaluate the impact of a carbon charge on the dispatch of energy resources — especially in neighboring regions.

It was part of an ongoing effort by the Integrating Public Policy Task Force (IPPTF) to determine how to price carbon emissions into NYISO’s wholesale electricity market.

The group, a joint effort between NYISO and the state’s Department of Public Service, also discussed a method for calculating marginal emission rates, the allocation of carbon revenues and the effect of carbon pricing on customer bills — all part of “Track 5” of the carbon pricing initiative.

IPPTF NYISO RGGI Carbon Charge
| PJM

The group also touched on issues related to “Track 4,” which covers the interaction of carbon pricing with other state and regional programs, such as the renewable energy credit and zero-emissions credit programs, as well as the Regional Greenhouse Gas Initiative.

Assumptions and Metrics

“We are interested in looking at not just the financial impacts but also at what happens to emissions,” said task force co-chair Nicole Bouchez, NYISO market design specialist.

“How do we assume the cases?” Bouchez asked. “Do we assume there’s a change in RGGI or not? In realization that we’re not going to be able to run dozens of permutations, what are the key assumptions?”

If the group “ends up modeling emissions in neighboring regions, for example in Ontario, which trades with MISO, then you have to model all of MISO’s resources,” she said. “While Ontario may look like a low-carbon import … if all it’s doing is causing MISO coal use to go up, then not so much.”

Marc Montalvo, representing the DPS Utility Intervention Unit, said, “If we’re designing a policy and implementation, if success is highly dependent on having perfect or near-perfect information about our neighbors’ emissions rates and those kinds of things, then it’s probably not a good policy in the first instance.”

Bouchez said the group’s May 7 and 21 meetings would focus “on how to structure the analysis, what questions, what metrics we’ll be reporting, etc.”

Defining Impacts

During a discussion of the impact of carbon pricing on consumer costs, Bouchez said the ISO’s locational-based marginal pricing (LBMP) represents “only the beginning of impacts on consumers because we’re also going to be looking at the return of these residuals associated with a carbon charge to consumers, so you can’t just look at the LBMP increase on its own.” The “residuals” refer to leftover money refunded to load under a carbon pricing scheme.

IPPTF NYISO RGGI Carbon Charge
| NYISO

Representing a coalition of large industrial, commercial and institutional energy users, Couch White attorney Michael Mager said his clients were seeking “two big things” from the impact analyses. First, “a thorough, unbiased analysis” of the impacts on market prices and what consumers are paying.

“And the second piece is, what are the emission reductions, if any, that reasonably could be anticipated if this were to be done,” Mager said.

New York could see some really material carbon reductions if it starts retiring unused RGGI allowances, he said.

“On the other hand, if nothing is being done to RGGI whatsoever, and it’s just going to simply reduce the price of allowances that are going to be then used up by other states such that there’s little to no reduction in carbon throughout the RGGI region, then this whole effort strikes us as somewhat symbolic and not getting much for any price impacts,” he said.

Howard Fromer of PSEG Power New York asked, “Consumer impacts compared to what?

“And the what is not identified here,” Fromer said. “Obviously, the what, in my mind, has to include the fact that New York state right now is already spending and writing checks on a monthly basis and potentially, over the period that we’re talking about, could be spending billions of dollars.”

Fromer said that, aside from considering dispatch issues, the task force process also needs to consider the impact of a carbon charge on price signals, demand response and investment in the state’s 40,000-MW generation fleet.

No Pot of Money

Stakeholders asked how the trend of increasing electrification — in the transportation sector, for example — should affect pricing carbon into the wholesale market.

Bouchez said many experts have told her the price of electricity has very little to do with electrification.

Bob Wyman of Dandelion Energy countered that electricity prices definitely affect consumer choices in New York City, where Consolidated Edison learned that city residents who install heat pumps use them for air conditioning but simply turn them off in winter because of high electricity prices for heating.

“Whether this approach is complementary or designed to supplant the mandated programs [such as the state’s Clean Energy Standard] … to the extent that you are supplementing the existing programs, the issue is always about what are the incremental benefits, does it affect dispatch, new investment, how are the effects by zones, and you have to address those transition overlap and windfall revenue questions as part of the impact analysis,” said James Brew of Nucor Steel Auburn.

IPPTF NYISO RGGI Carbon Charge
| NYISO

He said New York is relatively unique in trying to pursue both mandated and market programs, which means any analysis has to examine how the two programs interact.

David Clarke, director of wholesale market policy at the Long Island Power Authority, said carbon revenue collections within RGGI states would be a useful metric for examining the cost of abatement.

“I know we’re going to be looking at how much folks are paying for carbon allowances within New York as kind of the pot of money that we’re going to be splitting, but it would also be useful, depending on what scenario you are running, to find out what folks are collecting in terms of RGGI revenues within the other RGGI states,” Clarke said.

“There will be no pot of money,” Bouchez said. “I’ve been talking about them as residuals, which is how NYISO sees them, residuals being the difference between what we collect and what we pay out. How you allocate that within the wholesale settlements is a question. Do you give it back on a per-megawatt-hour basis? Do you give it back based on the impact of the increase in the LBMP?”

Warren Myers, DPS chief of regulatory economics, said that the joint staff are “nowhere near having an answer” on how to integrate multiple analyses into something useful but that “the work would get done by rolling up our sleeves” over the next few months.

The task force will next meet on March 19 to discuss Track 5 at NYISO headquarters.

MISO Cleared to Collect More Customer Info

By Amanda Durish Cook

FERC on Monday approved MISO Tariff revisions allowing the RTO to gather more information about proposed energy resources before they enter the interconnection queue.

Key among the changes is a requirement that a developer provide clearer upfront information about who will own a generating unit once its clears the queue.

In its ruling, FERC agreed the changes will “provide greater clarity to interconnection customers and greater transparency to all parties in the interconnection process” (ER18636). The new measures became effective March 1.

MISO FERC SPP Tariff attachment Z2 Western RTO
| © RTO Insider

Under the new rules, interconnection customers must provide MISO upfront documentation of “legally binding relationships” with parties that may claim ownership rights to a facility during the interconnection process.

MISO said the change will reduce the time it spends confirming ownership changes and will be necessary only when an interconnection customer “reasonably anticipates” another entity may claim ownership rights. The documentation would be limited to “that necessary to confirm the legal status and relationship of the relevant entities,” the RTO said.

Interconnection customers associated with a project can sometimes change during the definitive planning phase (DPP) of the interconnection queue, MISO said in its filing. In those cases, the RTO must confirm the legal status and relationship between the original and newly designated interconnection customers, creating an “administrative burden … that hinders the ability of MISO staff to administer other aspects” of the DPP.

“Requiring documentation proving legally binding relationships with entities that the interconnection customer reasonably anticipates may claim rights under the interconnection request upfront in the interconnection request form will ease administrative burden if a facility changes ownership later in the interconnection process,” FERC said, adding the change will help expedite projects moving through the DPP.

The commission rejected EDF Renewable Energy’s protest that MISO didn’t justify its need for the additional detail and that the changes would give the RTO more information than it needed. The company alternatively proposed that interconnection customers provide MISO with documentation “confirming a legally binding status upon requesting a name change,” rather than at the outset of the process. FERC said EDF was conflating name changes with changes in ownership status.

The Tariff revisions also require interconnection customers to provide MISO with IRS W-9 forms; banking information (including for other companies that may claim ownership in a generating facility); GPS coordinates for the point of interconnection for a project; descriptions of the number of generators, inverters, and transformers involved in the interconnection request; and additional contact information when a customer uses an agent.

They also expand the service options listed on MISO’s interconnection request form, allowing customers to specify a net-zero interconnection service request for an existing facility with no increase in capacity; indicate whether a request should be considered for the RTO’s fast-tracked process offered to small generating facilities; and inform MISO when a request for network resource interconnection service is intended for an existing facility.

The new rules additionally stipulate that net-zero interconnection customers must attach a system impact study to their requests and provide MISO with all necessary data before generator interconnection agreement negotiations can begin.

MISO Plan Provides Tx Treatment for HVDC Lines

By Amanda Durish Cook

CARMEL, Ind. — MISO and its stakeholders have agreed on a plan to treat merchant HVDC lines as transmission instead of generation when physically connecting to the RTO’s system.

A year in the works, the proposed Tariff revision would subject merchant HVDC lines to MISO’s traditional transmission schedule charges and make them ineligible for interconnection service. The RTO will file the proposal with FERC by the end of this month.

merchant hvdc lines miso
Godbole | © RTO Insider

Speaking at a March 14 Planning Advisory Committee meeting, MISO Director of Resource Utilization Vikram Godbole said the proposal does not prescribe any revenue plans for developers of merchant HVDC service. Developers would instead be responsible for determining the “net economic viability of their merchant HVDC project by considering their revenue streams and cost to connect to MISO transmission,” he said.

Some stakeholders asked how the RTO will treat transmission upgrades needed to connect HVDC lines in the interconnection queue.

“They’re not going to have interconnection rights,” Godbole said, adding that the lines will instead connect to the MISO system at a 0-MW status.

Under the changes, MISO will hold discussions with HVDC developers and owners before grid connection to determine whether a line is designed to withdraw or inject energy into the system, Godbole said. The RTO will require upstream generators contracting with injecting lines to procure network resource service through the interconnection queue, subject to system impact studies. Those units will be modeled like MISO’s other network resources, showing up in planning studies. Merchant HVDC customers that have secured injection rights and interconnection customers will share the costs of any needed network upgrades.

Meanwhile, merchant HVDC developers will be required to acquire MISO injection rights or a precertification that the system will be able to reliably handle the capacity and energy from proposed lines at the point of connection. (See “HVDC Interconnection,” MISO Eyes Small Queue Changes, Merchant DC Interconnections.)

Godbole acknowledged that MISO may eventually need to develop a more nuanced connection plan for merchant HVDC lines, but that, for now, it is focused on allowing such lines to connect to the system.

PJM PC/TEAC Briefs: March 8, 2018

PJM TEAC Duff-Rockport-Coleman project RTEP
Kern | © RTO Insider

VALLEY FORGE, Pa. — PJM’s plan to switch which side of a transformer is considered for cumulative ramping impact is “a win-win” because it models the system better without implicating expensive upgrades, the RTO’s Jonathan Kern explained to stakeholders at last week’s Planning Committee meeting.

The RTO was proposing to include in its calculations only transformers whose lowest terminal voltage level is at least 500 kV rather than any whose high side is at least 500 kV. PJM justified the change because distribution factors for transformers are generally closer to the lower-side system they connect to than the higher side. The plan was part of a larger package of revisions to Manual 14B developed through an annual review. Stakeholders endorsed moving the proposal to the Markets and Reliability Committee but not before examining PJM’s determinations.

PJM TEAC Duff-Rockport-Coleman project RTEP
Dolan | © RTO Insider

Kern said an analysis found that two transformers — the 500/138-kV Wescosville and 500/230-kV Ladysmith — could potentially be overloaded by the change at a cost of $18 million and $25 million, respectively. He said the change would only take effect starting with the 2023 Regional Transmission Expansion Plan, an initial analysis of which doesn’t show any impacts.

“There’s very strong evidence for the technical change we’re proposing to make here,” Kern said. “To us, it appears like a win-win change. In other words, it’s meeting the obvious technical intuition we have for generation delivery but also not creating any new overloads.”

However, American Municipal Power’s Ryan Dolan reminded everyone that no cost increases come without impact.

“I would argue that over $30 million of required upgrades wouldn’t be minimal,” he said.

External Capacity

PJM’s Aaron Berner successfully urged stakeholders to endorse rule revisions that would allow pseudo-tied external resources wanting to offer into the RTO’s capacity auctions to deliver into the energy market any additional generation beyond what’s authorized for capacity.

The RTO’s rules for external resources impose requirements that can limit how generation those units can offer into the Reliability Pricing Model.

“That doesn’t mean though that the transmission service is not deliverable for energy use,” Berner explained. “So with the addition of this language, the studies that PJM performed previously or would perform for new generation would still allow that generation to be delivered as transmission service for participation in the energy market.”

The revised language was added to changes developed for Manual 12 to address pseudo-tied capacity resources. Berner fielded several clarifying questions before stakeholders requested that PJM add detail to their proposed revisions.

“The current language does not explain in detail what you explained,” said James Manning with the North Carolina Electric Membership Corp.

Berner agreed to work with stakeholders on that issue, but he asked that they endorse the intent of the revisions so it can move on to the MRC.

Limiting Meetings Causing Stakeholder Strain

In explaining why proposed revisions to Manual 21 were only presented at the Planning Committee, staff said they were only trying to comply with stakeholder requests to limit meetings.

Bell | © RTO Insider

PJM’s Jerry Bell explained the revisions, which would change how generators are tested to receive and retain capacity interconnection rights (CIRs). Stakeholders argued that the changes are wide-ranging, requiring input from experts who don’t typically attend committee meetings, and asked why the considerations hadn’t been put to a task force or other high-level committees.

“This is really a generation operations issue, but we’re looking at it in the Planning Committee. We’ve got mostly transmission planners in the room here. We really need to expose this to all of the people this is really going to affect,” FirstEnergy’s Jim Benchek said. “These changes are pretty major.”

“I don’t necessarily think there’s any ill intent here, but it’s just that sometimes what looks to be just something for the Planning Committee has broader impacts,” said Adrien Ford with the Old Dominion Electric Cooperative. She suggested that PJM’s problem statement/issue charge process could have arrived at a result faster because the necessary stakeholder groups could have been identified up front.

“We’re trying to balance the needs of the stakeholders where we’ve gotten feedback about having too many other meetings and having the agendas jammed and the days of the week jammed with other meetings,” said Ken Seiler, who chairs the Planning Committee. He said he would confer with the chairs of the Operating and Market Implementation committees about how to handle the requests.

Stakeholders noted several concerns with the proposal, which would eliminate June from the summer testing period (leaving July through August) and require simultaneous testing of all resources at a plant except wind and solar units. They would have to be able to start within five minutes.

“If you were to call on all the units at a plant and apply the test simultaneously, the start-up costs could get quite expensive,” Benchek said, adding that his company didn’t favor the reduced testing period either.

Solar and wind would be exempt because they use their average capacity factor during the peak hours included in the testing, but all capacity factors will be determined by calculating the median rather than average performance going forward. Bell confirmed those calculations won’t become fully effective until 2021/2022.

Mike Borgatti with Gabel Associates was concerned that the proposed language changes didn’t adequately enunciate that units’ capacity factors wouldn’t be affected for three years.

Bell also walked stakeholders through analysis that shows that the 650 MW of non-dispatchable hydro generation might be overstated by 520 MW because the expected capacity factor of 20% shows that 130 MW is predicted to be available.

AEP Project Removed from RTEP Modeling

American Electric Power’s portion of Duff-Rockport-Coleman project has been placed on hold and will not be modeled in the 2018 RTEP, PJM told the Transmission Expansion Advisory Committee on Thursday.

Robert Bradish, AEP’s vice president of transmission grid development, informed PJM of the change in a letter Feb. 20. Bradish said the supplemental project was proposed to address voltage stability limitations and eliminate the special protection scheme at the Rockport plant by interconnecting the Rockport 765-kV station with the MISO Duff-Coleman 345-kV market efficiency project.

“The current generation situation at Rockport plant is quite different from the situation when this supplemental project was included in the 2015 RTEP,” Bradish wrote. “There is currently significant uncertainty regarding generation-related conditions which may affect future operation of the Rockport units. Certain of these generation conditions can only be addressed through coordination with third parties, regulatory proceedings and other circumstances outside of AEP’s control.”

Retirement Studies Update

PJM has completed reliability analyses on retirements at six generating stations and is conducting reviews for three others.

The retirements of Buggs Island 1 and 2 (138 MW), Bremo 3 and 4 (227 MW), and Bellemeade CC 1 (265.7 MW) are all effective April 16; Possum Point 3 and 4 (317.7 MW) and Chesterfield 3 and 4 (262.1 MW) are both scheduled for Dec. 1. PJM said it has asked Dominion Energy, the transmission owner for all the plants, to perform additional analysis to identify any required upgrades.

PJM said it identified no impacts from the scheduled May 3 closing of Evergreen Power United Corstack (25 MW) in Met Ed.

It is conducting analyses on the Morris Landfill Generator (1.9 MW) in ComEd and the Reichs Ford Road Landfill Generator (1.7 MW) in APS, both set for May 31, as well as FirstEnergy’s Pleasants Power Station 1 and 2 (1,278 MW), scheduled for Jan. 1, 2019. (See FirstEnergy Shutting down Unsold Coal Plant.)

Market Efficiency Update

PJM planners have selected a $25.4 million proposal by Baltimore Gas and Electric to address constraints on the Conastone-Graceton-Bagley 230-kV corridor after finding it cleared their reliability and cost/constructability analyses. The project (proposal 5E), which involves reconductoring and upgrades to equipment at the Conastone and Windy Edge substation, is expected in service in 2021. It will be recommended for approval at the Board of Managers meeting in April.

Planners said they won’t be recommending any market efficiency projects in the PPL zone after seeing the projected congestion benefits from the proposed Susquehanna–Harwood drop by about half under the base case because of a lower load forecast and changes in generation expansion since the start of the 2016/17 project window.

PJM is now developing assumptions for its 2018/19 RTEP long-term window, which it expects to open between November and February 2019.

Officials also said they expect to open a 60-day reliability project window in May or June.

Rory D. Sweeney & Rich Heidorn Jr.

PJM Operating Committee Briefs: March 6, 2018

VALLEY FORGE, Pa. — PJM will hold its spring restoration drill May 15-16, staff told attendees at last week’s Operating Committee meeting. Invitations will be emailed March 19 to the contacts listed in transmission owners’ restoration plans for the transmission operator, generation operator and training liaisons, PJM’s Alpa Jani said.

PJM Operating Committee Meeting DER Restoration Drill
PJM’s Operating Committee met on March 6th | © RTO Insider

Primary Frequency Response

PJM’s Glen Boyle said stakeholders’ work in the Primary Frequency Response Senior Task Force became more complicated and urgent after FERC issued Order 842, which requires all new generation that receives an interconnection agreement to provide primary frequency response. (See FERC Finalizes Frequency Response Requirement.)

The order silenced any debate about new facilities, so staff will instead focus on what should be required of existing units. The order could delay the PFRSTF’s work, but the group plans to vote on proposals after its March 21 meeting. Stakeholder endorsement votes will likely be completed in June.

Unit-specific Parameter Adjustments

Jani also reviewed the statistics about the number of unit-specific parameter adjustment requests that PJM received this year. The request period closed on Feb. 28.

All final determinations will be made by April 15 so they can be implemented by the start of the delivery year on June 1. Jani noted that soak time information is only for reference this year but will be added as a parameter and integrated next year.

Resilience Update

PJM Operating Committee Meeting DER Restoration Drill
Manno | © RTO Insider

PJM’s Dean Manno reviewed the RTO’s resilience roadmap and highlighted the next steps for 2018. PJM is evaluating the needs for “extreme events,” he said, including reserves and regulation requirements, transmission loading and triggers. Staff are also planning to review the weather/environmental and sabotage/terrorism emergencies sections of Manual 13 to see if anything should be added.

30-Minute Reserves

PJM’s Vince Stefanowicz explained staff’s thought process on developing a real-time 30-minute reserves product and announced that a problem statement and issue charge will be forthcoming in April.

Currently, 30-minute reserves are only procured in the day-ahead market, so when more primary reserves are needed, they’re moved in from secondary reserves, which only serves to reduce secondary reserves rather than bringing in more units. The new product would achieve that, he said, “not just move things from secondary into primary.”

Dave Mabry with the PJM Industrial Customer Coalition said that “perhaps a bigger audience” would be necessary to make such changes and asked if the Market Implementation Committee would become involved.

“Conceptually, I’m in agreement with you,” said PJM’s Dave Souder, the interim chair of the Operating Committee. He said the plan is to figure out the operational needs, then determine what other committees need to be involved.

Implementing DER Ride Through

The RTO is hoping TOs will take the lead on implementing “ride through” for distributed energy resources, PJM’s Andrew Levitt said. Ride through is the process of remaining connected to the grid during abnormal conditions. Despite being a “challenge” for large generators, Levitt said they’re required to do it while DERs are not.

Today, DERs can trip off very quickly and potentially over a wide variety of variables. However, there are already 4,000 MW of distributed solar generation in PJM today with expectations of that tripling in the next three years, making it a significant issue if they all trip when the grid is having issues.

“We think ride through is critical for DER,” Levitt said.

PJM recently published a draft revision of standards for DERs that would require ride through. However, it has no control over the net-metered solar that accounts for all the DER growth.

“We’re looking to follow the utilities’ lead on this topic … but we also anticipate a public stakeholder process” to support stability bulk energy supply and move toward a single standard for implementation, Levitt said.

Changing Tier 1 Reserve Estimates

PJM’s Joe Ciabattoni unveiled planned revisions to how Tier 1 reserves are estimated to address stakeholders concerns about major overestimates. (See “Investigating Improvements Based on Additional Cold Response Details,” PJM Operating Committee Briefs: Feb. 6, 2018.)

Ciabattoni | © RTO Insider

The RTO is proposing to cap spin max at a unit’s economic minimum and require that the spin ramp rate equal the economic ramp rate, he said.

“We find that during spin events this is an issue,” he said.

A TO representative who asked not to be named voiced concerns about reducing too much spin and asked that additional data be presented to explain the problem. Ciabattoni agreed.

“I just want to make sure we’re actually seeing a problem there as opposed to fixing a problem that doesn’t exist because there’s no way a resource could tell if there’s going to be a Tier 2 payment,” the TO representative said.

Tom Blair of the Independent Market Monitor said the issue is exacerbated because of how the reserve market is set up.

“There is no penalty for Tier 1 synchronized reserve not responding. There is, however, a significant incentive to overestimate your Tier 1 reserve,” he said.

Blair explained that the reserve market is set up so that units can earn enough money that they still make a profit even with the penalties that occur if they don’t respond when called upon.

Scarpignato | © RTO Insider

“I think directionally this is worthwhile, probably helpful,” said Carl Johnson, representing the PJM Public Power Coalition.

Calpine’s David “Scarp” Scarpignato said another issue is that scarcity pricing is not being triggered when it needs to be and that “the issue is much broader than this.”

RAS Removed

Commonwealth Edison is removing the Davis Creek remedial action scheme (RAS). The plan was needed to prevent thermal overloads in the event of losing a 345-kV line to the substation by auto-closing a 345-kV bus tie at the station.

A supplemental project to expand the 345-kV bus at the substation is expected to be completed by the end of the year.

Rory D. Sweeney

Overheard at Transmission Summit East 2018

WASHINGTON — Transmission developers, planners and regulators gathered last week at the Washington Marriott Georgetown hotel for the three-day Infocast Transmission Summit East. While grid security was on the minds of all who attended, speakers also had plenty of opportunities to vent about FERC Order 1000 and RTO planning processes — as well as poke fun at Ted Koppel.

DOE Official Briefs ‘North American Model’

Walker | © RTO Insider

Bruce Walker, assistant secretary of the Office of Electricity Delivery and Energy Reliability at the U.S. Department of Energy, briefed attendees Wednesday on five initiatives by the department to enhance grid security.

The most ambitious, by the department’s Grid Modernization Lab Consortium, is developing a “North American all-energy systems model” that includes all the grid operators across North America and identifying their interdependencies.

“Once we’ve got this model, we’ll be able to do real-time analysis [and] next-worst-case analysis, so when an excursion occurs on any one of the major systems in the United States or Canada or Mexico, we’ll be able to run it and understand what that means and what the next-worst piece of equipment or system is to lose, so that we can proactively act to prevent that, whether it’s providing physical security, whether it’s changing the load flows on the grid to lessen the load or demand in one particular place,” Walker said. Many of these actions would be taken by RTOs, he said.

The model will be so comprehensive, he said, that it will be able to do “N-K” load-flow analysis, with the “K” standing for assets that aren’t traditionally considered part of the electric grid. (See related story, “Beyond N-1,” Tx Summit Attendees Struggle to Define ‘Resiliency’ Problem.)

Another initiative is “megawatt-scale storage strategically being utilized throughout the grid.” Walker said this initiative ties in with the North American Model, which will allow the department to “identify where the best investments of these” storage assets would be.

This raised the eyebrow of Rob Gramlich, president of Grid Strategies. “‘Identifying best investments’: that sounds like a market function. How does this initiative interact with the market?” he asked.

“Because we’re focused on the resiliency component — and then we’re specifically focused on critical infrastructure — … the market actually has no place in making the determination for those investments,” Walker responded. “So part of why we got FERC, NERC and DOE looking at the system and building this model is we come at it from slightly different angles. FERC’s angle is a bit more market-driven; NERC’s is more reliability-driven; DOE has got very specific requirements, being the sector-specific agency for cybersecurity in the energy industry, focusing in on critical infrastructure throughout the United States.”

Impact of Ukraine-style Attack Would be Less

A cyberattack on the U.S. grid by a foreign power such as the one experienced by Ukraine in 2015 and 2016 is certainly possible, several experts said in a Wednesday panel on cybersecurity.

But Ukraine lacks the basic protections and infrastructure of the U.S., meaning such an attack would be far less disruptive and destructive here, they said.

From left to right: Mark Scott, D.C. Homeland Security Emergency Management Agency; Michael D. Melvin, NIPSCO; Col. Victor Macias, National Guard; Ralph King, EPRI; Michael Garcia, National Governors Association; and Brian Harrell, George Washington University. | © RTO Insider

Or as moderator Brian Harrell, senior fellow at George Washington University’s Center for Cyber and Homeland Security, quipped, “I don’t know too many utilities here in the United States running pirated versions of Windows XP on their systems. So, there are some differences here.”

The general consensus among the panel, which included a National Guard colonel, was that utilities need to be incentivized to do more than the minimum required by NERC, as well as be on guard for insider threats.

But the panelists unanimously labeled as off-base the assertion made by broadcast journalist Ted Koppel in his book “Lights Out” — the mention of which drew laughter from the audience — that the U.S. is susceptible to a catastrophic attack and that industry and government are not taking the threats seriously.

Flaws in Planning Processes

Many speakers complained about the transmission planning processes in RTOs, including the competitive and interregional processes.

Zadlo | © RTO Insider

On a Thursday panel discussing the effects of renewable energy resources on transmission planning, Invenergy Senior Vice President Kris Zadlo said he doesn’t “think transmission planning is happening.”

“Operating lines that [are] 2% overloaded or replacing transformers: that’s not transmission planning,” Zadlo said. “That’s asset management.”

He pointed to American Electric Power’s Wind Catcher Energy Connection Project, which Kelly Pearce, director of contracts and analysis for the company, had briefed attendees on earlier in the day. The project would be the largest wind energy facility in the U.S at 2 GW, with a dedicated 765-kV tie line from the Oklahoma Panhandle to Tulsa.

From left to right: Kamran Ali, AEP; Barbara Clemenhagen, Customized Energy Solutions; Jack McCall, Lindsey Manufacturing; and Ed Tatum, American Municipal Power. | © RTO Insider

“Folks are trying to find end-arounds,” Zadlo said. Wind Catcher is a “360-mile end-around because SPP’s transmission planning process has failed. … Quite frankly it’s disgraceful that we have to wait three to five years for an interconnection study to be processed by utilities and by ISOs.”

Fox | © RTO Insider

Kip Fox, president of Electric Transmission Texas, said, “One thing we do notice across all of the RTOs that everybody should kind of think about is we’re not seeing a lot of interregional” projects. “We are not seeing projects that are going across RTOs. And unfortunately, that’s where the big bang for the buck economically is going to be. And usually I find it’s a fight over who’s going to pay for that project, rather than whether that project makes sense.”

On a separate panel Thursday, Kamran Ali, AEP vice president of grid development, noted that between 2012 and 2016, PJM identified 72 projects that were open for competition. Of those, only three ended up being assigned to nonincumbent utilities, he said.

Trump Admin’s Effects?

Speakers at the conference uniformly dismissed the actions of the Trump administration as having any effect on the growth of renewables and the retirement of coal-fired generation. Even as one attendee announced to the conference that President Trump had imposed tariffs on steel and aluminum imports Thursday afternoon, panelists were not concerned.

“There’s something interesting that’s going to happen in 2020,” Zadlo said. “It’s not that the [production tax credits] are going to run out.” Nor is it the next presidential election year. “In 2020, millennials will be over 50% of the workforce. Have you guys polled the millennials as to what their feelings and thoughts are regarding renewable energy? If you haven’t, you better. Because they want it.”

— Michael Brooks