Search
`
November 18, 2024

PJM Planning Transmission Expansion Advisory Committee Briefs

VALLEY FORGE, Pa. — General assumptions regarding winter operations will need to be replaced with actual data to improve PJM’s winter resource adequacy analysis, staff told the Planning Committee last week.

“There’s a propensity for our load model to under-forecast the winter load,” PJM’s Tom Falin said. “This is of concern to us.”

The analysis also found that while the generation forced outage rate for winter rose just 1% from 2007 to 2015, winter’s standard deviation is 4%, more than double the 1.7% for summer. Falin presented a graph that highlighted the increased uncertainty, showing that in one winter week, the forced outage rate could be anywhere from 4 to 12%. Noting that as many as 181 transmission elements, including lines and transformers, were on planned maintenance at some point during January, he questioned whether they could result in deliverability problems.

winter resource adequacy PJM
Plot of Mean With Band of + / – One Standard Deviation | PJM

“To get a handle on that will be a challenge for us,” he said, adding that it’s another area that’s not being fully captured in PJM’s loss-of-load expectation (LOLE) studies.

One area to look at might be equivalent forced outage rates – demand (EFORd), which measures the probability that a unit will fail when needed. PJM’s current EFORd calculation is an annual measurement that is independent of other EFORds, weather and other variables.

Falin questioned whether it made sense to develop EFORds that consider seasonal variables. Additionally, the class averages for wind and solar are based on summer measurements, which underestimates wind’s winter availability while overestimating that for solar.

Another issue is modeling. PJM’s modeling tool, PRISM, “is going to say there’s virtually a 0% chance of a 13% outage rate,” Falin said. “The problem is we’ve seen it.”

“We may be getting to a point where wind [generation] captures a big-enough share where we should start capturing turbine’s actual performance and not just assume it’s 13%,” he said.

In November, stakeholders approved a problem statement and issue charge to review PJM’s load forecasting and planning models and methodologies to determine whether the RTO is properly calculating the amount of capacity needed in winter to meet its LOLE targets. The initiative was proposed by economist James Wilson on behalf of consumer advocates for Maryland, New Jersey and Delaware. Wilson and others have questioned why the summer-peaking RTO requires identical amounts of capacity in summer and winter. (See PJM Stakeholders Reject CP Rule Changes, OK Additional Study.)

Staff Moving Forward on Memorializing Competitive Planning Process

PJM staff presented the PC with the first product of their meetings on redesigning the Transmission Expansion Advisory Committee, a new Manual 14F: Competitive Planning Process. The manual mostly codifies processes that previously had been done informally. (See PJM Making Cost Consciousness a Focus for RTEP Redesign.)

PJM’s Mike Herman | RTO Insider

PJM’s Mike Herman, who is overseeing the project, said he had been told by Dave Anders, the keeper of all institutional knowledge regarding the RTO’s stakeholder process, that he can’t remember the last time it created a new manual. “So we in planning must be doing something right,” Herman joked.

While PJM acknowledged it’s already received substantial feedback about the manual, staff urged stakeholders to provide all comments for next month’s meeting.

“We would like to move this along next time,” Vice President of Planning Steve Herling said. “We would really appreciate people going through it [and bringing any issues to the April meeting]. The only way we’re going to find out if this works really well if you all test it out and tell us what you like.”

PJM’s Steve Herling | © RTO Insider

Public Service Electric and Gas’ Alex Stern foresaw an enforceability issue. “Although it is true that PJM hasn’t policed incumbent transmission owners to ensure they are building to minimum design standards, they’ve never had to because state officials more than do that job,” he said. When there’s a problem, customers often call state officials, who call the local utility.

“What happens next is typically things get fixed so that calls … don’t happen further and customer service is at an appropriate level,” Stern said. “State officials aren’t going to know [whom to contact at non-incumbent transmission developers]. When something’s not working, they’re likely going to call their local utilities and PJM’s government relations people.”

Herman also presented proposed administrative updates to Manual 14B to change all occurrences of “special protection system” to “remedial action scheme” per a change to the NERC glossary of terms.

New Design Requirements and Procedure Developments Presented

The Designated Entity Design Standards Task Force introduced its first product at the PC meeting: a document setting standards for overhead transmission. The task force will also be developing standards for substations, system protection, control design and coordination, staff said.

PJM also presented its planned structure for complying with standards released last fall by NERC on geomagnetic disturbance events. The structure includes a five-year implementation schedule that won’t produce assessment results until 2021. Full GMD vulnerability results won’t be available until 2022, when PJM plans to begin developing any necessary corrective plans.

PJM Offers Four RMR Contracts

PJM told the TEAC it has offered generation owners in New Jersey and Virginia reliability-must-run contracts for four units, all of which have received FERC approval.

The New Jersey units — Rockland Capital’s coal-fired B.L. England Units 2 and 3 in the Atlantic City Electric transmission zone — were asked to run until previously approved baseline transmission upgrades are completed. The upgrades were expected to be completed within the next two years, but delays to related projects have made the timeline indeterminate.

PJM also is asking Dominion Energy to keep operating its Yorktown coal-fired Units 1 and 2 until a transmission solution is approved. The plants, on Virginia’s middle peninsula, have been the focus of years of controversy. Their license was extended to April, but environmental groups have been pushing for their closure. Dominion has sought support for installing a 500-kV line from the mainland to the south, but environmentalists have fought that as well. Without approval of the transmission line, PJM has identified reliability issues that would arise if the Yorktown units close. (See Dominion Says Blackouts the Only Solution for Va. Peninsula.)

— Rory D. Sweeney

SPP Briefs

The odds of SPP and MISO conducting a second joint study dropped last week with the announcement that the RTOs’ respective regional reviews are not lining up as expected.

spp miso z2 task force
Bell © RTO Insider

The two RTOs had hoped to conduct a broad joint study starting as soon as this year that would evaluate regional and interregional projects on the same timeline, eliminating a major stakeholder complaint. (See SPP-MISO IPSAC Turns Attention to 2017 Study.) However, staff told the MISO-SPP Interregional Planning Stakeholder Advisory Committee on Thursday that their respective timelines are not lining up as expected.

“That created issues in scoping and planning. We hope to provide more detail and a schedule,” Adam Bell, SPP’s interregional coordinator, told the IPSAC. “We’re both very committed to doing a study to the extent it makes sense. We’re looking at what flexibility SPP has and what flexibility MISO has to work through the challenges this has presented.”

Bell said MISO’s Regional Transmission Overlay Study (RTOS), which will end in December 2019, is targeting the end of next year to determine transmission projects that can address the RTO’s shifting resource mix. (See MISO Begins 3-Year Tx Overlay Study.) However, SPP’s transition to its new Integrated Transmission Planning process won’t result in the release of an economic study until October 2019.

spp miso z2 task force
| MISO, SPP

Under the current timelines, MISO would spend 2019 building a business case around an approved portfolio. SPP is not scheduled to begin building its economic model until the third quarter of 2018.

“The timing is a little off in our ability to go through the process as we had originally envisioned,” Bell said. “It looked like they would match up very well. We would have board approvals at the same time, do interregional work. … Jumping into something before we have all that worked out is not something we need to do.”

Bell reassured stakeholders the two RTOs would still conduct “some sort” of joint planning in 2017 as part of their desire to take a more comprehensive look at reliability and economic transmission upgrades. He said staff would work with their regional stakeholder groups to resolve the misaligned timelines. A follow-up conference call has been tentatively scheduled for April 24.

“We all see the benefit of doing this broader study,” Bell said. “We pretty much know when things will start and finish. We’re trying to see now if there is any flexibility” in the timelines.

Several stakeholders were confused as to why staff had waited until the IPSAC meeting to bring the issue into the open. ITC Holdings’ Marguerite Wagner pointed out one of the goals of SPP’s new ITP process, which was approved last July, was to align it with MISO’s timeline.” (See “SPC, MOPC Approve Improvements to SPP’s Tx Planning Process,” SPP Strategic Planning Committee Briefs.)

“As far as I know, the SPP process has been developed for months,” said the Wind Coalition’s Steve Gaw. “I’m not sure why it’s this meeting [that you discovered] you have an issue.”

“We’ll get back at the RTO regional level and work on the schedules a little bit,” promised MISO Director of Planning Jeff Webb. “It’s a good opportunity to get them back in alignment.”

The IPSAC spent much of the meeting reviewing each RTO’s planning processes and efforts being made to improve them. The first joint study between the two entities failed to produce a single interregional project; they have focused their efforts since on improving their coordination. (See SPP, MISO Conclude Joint Study Empty-Handed.)

“Someone smarter than me once said the definition of insanity is doing the same thing over and over and expecting different results,” said Eric Thoms, MISO’s manager of planning coordination and strategy. “We want to be more forward-thinking and understand why we are getting drastic differences in our interregional outcomes and studies.”

As an example, MISO’s Ling Lao detailed to stakeholders how the RTOs calculate the adjusted production cost (APC) differently for the Coordinated System Plan (CSP), a separate interregional effort from the joint study. The calculation is used for allocating costs between the two entities.

spp miso z2 task force
| MISO, SPP

Lao said the MISO-SPP joint operating agreement outlines the APC-calculation methodology at a high level, similar to SPP’s regional methodology. SPP uses the load LMP for pricing purchases and generation LMP for pricing sales. MISO, on the other hand, uses the generation LMP for pricing both purchases and sales in its metrics.

The load LMP is usually higher than the generation LMP when the system is congested, yielding higher project benefits or APC savings, Lao said. Thoms said MISO is currently evaluating changes to its APC calculation in its Regional Expansion Criteria & Benefits Working Group.

“Using different calculation methodologies introduces equity concerns,” said SPP Director of Interregional Relations David Kelley. “It doesn’t necessarily mean we know one method is better than the other. Could it be MISO is underestimating its benefits? Yes, but on the other side of the fence, you would say SPP is overestimating its benefits.”

The APC was part of a screening process that has whittled the CSP’s list of seven potential joint transmission projects down to three. (See “SPP-MISO IPSAC Turns Attention to 2017 Study, SPP Briefs.)

Staff said the three preliminary projects passing the study criteria are:

  • A second 345/115-kV transformer in western Minnesota;
  • A 161-kV line near Kansas City; and
  • A 345-kV line and a 345/161-kV transformer near Springfield, Mo.

AECI Joint Projects Move Forward

The Springfield project would be in the same area where SPP’s joint CSP with Associated Electric Cooperative Inc. identified two projects: a 50-MVAR reactor at Springfield’s 345-kV Brookline substation, and a new 345/161-kV transformer at AECI’s Morgan substation and an uprate of a related 161-kV line.

SPP’s Seams Steering Committee took up both projects during its March 8 meeting. The Brookline reactor has an estimated cost of $1.1 million, below the $5 million minimum for SPP seams projects. However, staff said it sees a benefit in continuing forward with the project.

The SSC will meet again March 24 to discuss the project, in hopes of making a recommendation to the Markets and Operations Policy Committee in April.

The Morgan transformer was included in the 2017 ITP 10-Year assessment that was approved by the MOPC and SPP’s Board of Directors in January. The project, valued at $9.2 million, is contingent on reaching a cost-allocation agreement with AECI.

SPP’s monthly market-to-market report to the committee showed MISO sent another $250,762 in M2M payments to its seams partner in January, thanks to a net 230 hours of binding. SPP paid MISO just more than $51,000 for 126 hours binding over 11 temporary flowgates.

MISO has made $14.5 million in M2M payments since the RTOs began in the process in March 2015. When SPP completes two years of the M2M process in March, it will be at the same stage MISO and PJM were when they developed their targeted market efficiency projects on their seam.

The projects address historical congestion issues on the MISO-PJM seam, and MISO and SPP said they are committed to following a similar approach later this year. The process focuses on small, low-cost, short-lead-time upgrades targeted at specific, historical congestion issues.

Z2 Task Force Narrowing its Alternatives

The Z2 Task Force met in Dallas on March 8 to review PJM and MISO’s processes for incremental long-term congestion rights, which the group is considering as an alternative to its current crediting system for transmission upgrades. (See SPP Z2 Task Force Looks for Best of Proposals.)

The task force developed a list of alternatives for sponsored upgrades, transmission service upgrades and generation interconnections. ILTCRs remain a potential solution in each of the three categories, along with the existing Z2 processes, albeit with some modifications.

spp strategic planning committee transmission
KCP&L’s Denise Buffington | © RTO Insider

American Electric Power’s Richard Ross and consultant Dennis Reed will also bring proposals to the group’s next meeting. The task force plans to narrow down the list of proposals and then develop the details in order to meet a July deadline with the MOPC.

“We’re a task force,” Kansas City Power & Light’s Denise Buffington, the group’s chair, reminded her team. “We can propose language, but we are going to address the policy question with the board first.”

Buffington said it would be up to the board whether a task force or some other group drafts new policy language.

Microgrid Kool-Aid and National Security

By Steve Huntoon

The microgrid Kool-Aid keeps gushing out of the firehose. I wrote a while back about why microgrids are an irrational throwback to the utility islands of the late 19th century.[1]

microgrids national security
Huntoon

In a nutshell, microgrids cannot improve on the efficiency of centralized, least-cost dispatch. And in terms of adding reliability, authoritative case studies by the New York State Energy Research and Development Authority found that microgrids would make sense only if annual customer outage time was measured in weeks, rather than the reality of a couple hours.

Yet microgrid proposals continue to proliferate. Especially where subsidized with Other People’s Money.[2]

This column focuses on a microgrid study involving our military bases.[3] This is important not only because taxpayer money is involved, but because our national security is involved.

This study, by a consultancy called Noblis, with assistance from ICF, concludes that replacing backup diesel generators at individual military buildings (the status quo) with diesel/natural gas microgrids at military bases would save money.  Their concept is shown in the study’s Figures 4 and 5.

The study includes an incredible amount of modeling and data, no doubt costing its sponsor, Pew Charitable Trusts, a ton of money.

Yet the study is profoundly wrong. The profound error is shown by this “Ownership of infrastructure” pie chart from a Government Accountability Office study,[4] showing who owns the infrastructure responsible for significant outages.

You can see that 87% of outages on military facilities arise on the military’s own distribution systems. Microgrid generation would be dependent on these distribution systems to deliver electricity to individual buildings. Thus, microgrids would cause individual buildings to lose backup for 87% of outages — eliminating the vast bulk of backup.

How could such a profound error be made? The study wrongly assumed that distribution system outages aren’t significant, saying: “Although inside-the-fence problems account for some (unknown) share of all outages, on-base problems can generally be solved through improved maintenance of the base and straightforward investments (e.g., keeping trees trimmed and putting wires underground).”

Instead, on-base problems account for 87% of all outages.[5] And if they were easily avoided, they would be.

In Rumsfeldian parlance, on-base problems are not a “known unknown,” but instead are a “known known.” The study’s profound error was not recognizing this known known.

And another important national security consideration: cybersecurity. The Noblis study talks a lot about cybersecurity, but nowhere does it acknowledge that for microgrids to function as intended, they must have communications links with the greater grid, exposing them to the same cyber risks as the rest of the grid. Backup generators at individual buildings do not need any communication link outside the building.[6]

Beyond these two vital national security considerations, please note one other glaring oversight in the study. This one involves the estimated cost of microgrids.

The study goes through a lot of hypothetical numbers to come up with a capital cost of $17.4 million for a hypothetical microgrid of 24 MW, which works out to $725/kW.

Problem: The Defense Department’s most recent microgrid project at Marine Corps Air Station Miramar in San Diego cost $20 million for 7 MW.[7]  That works out to $2,857/kW, which is about 400% of the study’s cost estimate. The study mentions the Miramar microgrid but somehow doesn’t connect the dots to its project cost.

An ounce of fact is worth a pound of hypothetical.

And speaking of fact, the nation’s “flagship” microgrid at the University of California, San Diego flunked its acid test in the Southwest Blackout of 2011. The campus shut down with the rest of San Diego.[8]

You can’t make this stuff up.

 

Steve Huntoon is a former president of the Energy Bar Association, with 30 years of experience advising and representing energy companies and institutions. He received a B.A. in economics and a J.D. from the University of Virginia. He is the principal in Energy Counsel LLP.

[1] http://energy-counsel.com/docs/Microgrids-Wheres-the-Beef-Fortnightly-November2015.pdf.

[2] Not all the news is bad. Pennsylvania’s consumer advocates got PECO Energy to abandon a $35 million microgrid dalliance, and it appears hundreds of millions for Commonwealth Edison microgrids got cut from the Illinois Future Energy Jobs Act, approved in December, which provides zero-emission credits for Exelon’s nuclear generators.

[3] http://noblis.org/media/b6a465e0-4200-42d8-9377-5f20251e52c0/docs/Environment/Power%20Begins%20at%20Home-%20Noblis%20Website%20Version_pdf.

[4] http://www.gao.gov/assets/680/671583.pdf. Figure 3: Disruptions lasting eight hours or longer in fiscal years 2012-14 as reported to GAO by 18 Defense Department installations inside and outside the continental U.S. The data include wastewater and potable water disruptions, but the vast majority of the disruptions are electric.

[5] This is consistent with outage causation outside of military facilities. About 90% are attributed to the distribution system, as opposed to the higher voltage transmission system. See http://www.eei.org/issuesandpolicy/electricreliability/undergrounding/documents/undergroundreport.pdf, Figure 3.3. (Compare the customer interruptions on the combined transmission/distribution system to interruptions on the distribution system alone). One driver of this is that the transmission system is designed with redundancy, so that if one element (a transmission line, a transformer, etc.) fails, there is no loss of service. The distribution system generally is not designed with such redundancy.

[6] Individual backup generators also would seem less vulnerable to electromagnetic pulses (EMPs) because they are simpler, not connected to the grid, and do not operate unless there is an outage. Noblis says that EMPs are “beyond the scope of this report” (footnote 10), which begs the question: “Why?”

[7] https://microgridknowledge.com/military-microgrid-projects/.

[8] http://www.eenews.net/stories/1059996047 (“The university’s two 13.5-MW Trident turbines were running full-bore when power from the utility abruptly went dead. With no time to shed their load, the turbines also shut down, and the campus lost electricity.”)

MISO to Fix Recently Discovered Tariff Mistake

By Amanda Durish Cook

CARMEL, Ind. — MISO will file with FERC to correct a recently uncovered eight-year-old Tariff mistake related to the RTO’s day-ahead margin assurance payment.

The RTO has found that Module C of its Tariff contains language saying that any resource that incurs an excessive or deficient energy deployment charge during one hour will be “ineligible for [day-ahead margin assurance payment] in that hour and all remaining hours in the day-ahead transmission provider commitment period.”

day-ahead margin assurance miso tariff
Page from MISO Module C Tariff | MISO

The problem: MISO prohibits the receipt of the day-ahead margin assurance payment only for the hour in which the resource incurred the charge; it does not observe an hours-long disqualification. The Business Practice Manuals limit payment ineligibility to the single hour the charge was incurred. A longer disqualification would restrict dispatch flexibility, the RTO said.

Bladen | © RTO Insider

Despite the discrepancy between the Tariff and manuals, settlements have reflected guidelines in the latter since the beginning of MISO’s ancillary services market in 2009, said Jeff Bladen, executive director of market design. The erroneous language does not represent current or historical practice, Bladen said, and the error is not repeated in BPM language or MISO training manuals.

“The practice described in the Tariff was neither the intended method nor has it ever been used by MISO before or since 2009,” Bladen said at a March 9 Market Subcommittee meeting.

MISO will submit a Section 205 filing with FERC to remove the Tariff language and payment eligibility will carry on as usual, Bladen said.

“MISO immediately reported the issue to the FERC Office of Enforcement,” Bladen said. The error was uncovered during “unrelated” Tariff research.

Bladen said neither MISO nor its Market Monitor support resettlements, and no gaming was discovered.

David Sapper of Customized Energy Solutions asked what efforts the RTO could make in the future to catch Tariff errors.

“We are regularly undertaking compliance reviews. … We are subject to FERC compliance reviews,” Bladen said. “The level of obscurity of this Tariff language is evidenced by the fact that this wasn’t uncovered during those reviews.”

Overheard at NECA Renewable Energy Conference

AUBURNDALE, Mass. — About 200 people attended the snow-delayed Northeast Energy and Commerce Association Renewable Energy Conference on March 6. Here’s some of what we heard at the conference, which was rescheduled after a February snowstorm forced cancellation of the original date.

Offshore Wind

Offshore wind was a frequent topic in the opening session on emerging trends in renewables, which featured Matthew Morrissey, vice president of Massachusetts operations for Deepwater Wind.

NECA renewable energy conference
Morrissey (L) and Fioravanti | © RTO Insider

The company, which began operating the nation’s first ocean-based turbines off of Block Island, R.I., in December, won a contract from the Long Island Power Authority in January for a 90-MW wind farm off the island’s Southern Fork. It also hopes to grab a piece of the big prizes to come: Massachusetts and New York have set goals for a combined 4 GW of offshore wind by 2030.

Unlike in Europe, which has a mature offshore industry, the U.S. does not have a fully developed supply chain for developers. Thus, Morrissey said, his company has been tapping the expertise and supply chains of offshore oil and gas drillers.

“There is a lot of commonality between the expertise and innovation that the United States has developed in that industry — putting large structures in the water — and we wanted to tap that both for our benefit but also because … we have to keep costs coming down, and in order to do that you have to have local, stateside … manufacturing,” he said.

Morrissey and fellow panelist Richard Fioravanti, a principal with engineering and scientific consulting firm Exponent, said they were not overly concerned about the federal government reducing its role in energy research under the Trump administration.

NECA renewable energy conference
| © RTO Insider

“I see [renewable power] as a large, growing opportunity, and when there are opportunities, money follows,” Fioravanti said.

“I would say that 10 years ago, a slowdown in research would have been a problem,” Morrissey said. “But for the 10 or 15 or 20 years, the industry giants — like Siemens and General Electric and Vestas — [will be] driving innovation from a blade design point of view. And a lot of the foundation work they’ve done in the last 20 years — both in the U.S. oil and gas industry as well as the European offshore wind — with fixed bottom foundations, will drive the growth and cost curve downward … regardless of R&D coming out of Washington.”

Morrissey said the offshore industry also can seek support in D.C. by touting its job creation potential.

“When you look at the kind of places with offshore wind-created economic opportunity, those places tend to look like post-industrial, urban forgotten cities like Fall River or New Bedford [Mass.] or other cities like that along the Atlantic seaboard, which actually tend demographically to look a lot like southern Ohio or western Pennsylvania [where Trump did well in the November election]. So we think that there is an underlay of opportunity to talk to the Trump administration about.”

New England’s Duck Curve

Giaimo | © RTO Insider

Michael Giaimo, senior external affairs representative for ISO-NE, used “duck curve” slides to demonstrate how growing solar photovoltaic penetration is affecting the RTO’s ramps and system peaks. The RTO had 1.9 GW of behind-the-meter solar PV as of the end of 2016, more than two-thirds of it in Massachusetts.

While increasing PV boosts the need for ramping capability during the daylight, it does not affect the system peak in the winter, which typically occurs at about 7 p.m.

But PV generation could begin causing minimum generation emergencies in spring afternoons once PV generation reaches 3 GW, the slides showed. In the summer, increasing amounts of PV will push the net load peak later in the day, from 5 p.m. at current penetration, to 6 p.m. once penetration reaches 3 GW and 7 p.m. at 6 GW or higher.

“The low demand on a normal traditional day is like in the 3 a.m. timeframe,” Giaimo explained. “When you start getting about 3,000 or 4,000 MW of solar, our new low demand for the day happens about 3 in the afternoon. We [are going] from a system that had a low at 3 a.m. to now a system that has a low at 3 p.m.”

A Handful of States Writing the Rules on Community Solar

NECA renewable energy conference
Graber-Lopez | © RTO Insider

Eric Graber-Lopez, president of BlueWave Capital, talked about the delayed promise of community solar, noting that solar power adoptions still retain a “barbell” shape, with more than 90% of the market in residential rooftop panels or utility-scale facilities.

Legislative and regulatory debates, net metering capacity limits, program transitions and interconnection problems “have pushed back the promise of community solar,” Graber-Lopez said. “The U.S. installed about half of what it expected to install in 2015, and it was expected to install about two-thirds [of earlier estimates] in 2016.”

Community solar — which Graber-Lopez argues is a “proxy” for distributed generation in states such as Massachusetts — provides a way for renters, apartment dwellers and low-income housing residents to participate. “The problem is there’s no such thing as a DG industry. It varies state by state,” he said.

Massachusetts has been number two to California in DG deployment every year since 2014. Massachusetts, Colorado, Minnesota and New York account for 97% of the national pipeline for community solar over the next five to six years, he said.

“So there’s a lot of talk about the deployment of DG — and by extension the deployment of community solar — but the fact is that there are four states that are setting the standard for how this industry is going to look going forward,” he said.

Another 10 states are pursuing regulations or legislation “trying to either create, stop, modify or enhance DG,” he said.

Ex-DOE Official Hopes Climate Progress is in Economy’s ‘DNA’

Knobloch | © RTO Insider

In a keynote speech, Kevin Knobloch, chief of staff for the U.S. Department of Energy between 2013 and 2017, said the Trump administration may not do as much to reverse Obama-era climate policies as some fear.

President Trump and EPA Administrator Scott Pruitt, who have expressed skepticism over humanity’s role in global warming, are expected to attempt to cancel the Clean Power Plan. Trump also may withdraw the U.S. from the Paris Agreement on climate change.

But Knobloch, a former president of the Union of Concerned Scientists, said the renewable energy gains made during Obama’s term won’t be reversed.

“The Department of Energy’s early and robust investment in clean energy and low-carbon technologies, with similar investments by industry and the research universities, coupled with forward-leaning and clear public policies, have contributed to dramatic cost reductions and increased deployment of clean energy and ultra-efficient technologies,” Knobloch said. “And clean energy companies, like many of you represented here in this room, are consequently … well positioned to lead and compete in the rapidly emerging multi-trillion-dollar market for clean energy technologies.”

He noted that 195 countries signed the Paris Agreement to reduce their carbon emissions. That’s “195 markets for clean energy, renewable energy,” he said.

Knobloch said the dramatic budget cuts proposed by Trump to EPA and other domestic agencies to fund Defense Department increases would require undoing Congress’ sequestration rules.

He also noted that Congress’ last two major energy bills — the Energy Policy Act of 2005, which authorized loan guarantees for greenhouse gas control technologies and tax credits for alternative energy producers, and the 2007 Energy Independence and Security Act, which updated energy efficiency standards for appliances, residential boilers and other equipment — were approved with bipartisan support. He predicted Republicans such as Sen. Charles Grassley (R-Iowa) would fight any early termination of the wind production tax credit, which is due to be phased out over three years, ending after 2019.

| © RTO Insider

“We also know that it is not so easy to reverse rules like the Clean Power Plan or the energy efficiency rules … with their extensive … rounds of formal public comment periods, prospects of legal challenge. These are all designed on the foundation of laws that were directed by the Congress.

“My hope is having achieved or made dramatic progress toward a lot of those goals, that renewable energy, energy efficiency … is now in the DNA of the economy,” he said. “Those jobs are real. Those tax payments are real. The business plans and technology investments are all real and that that will carry on.”

Lack of Tx in Multistate RFP Puzzles Developer

NECA renewable energy conference
Conant | © RTO Insider

About 900 of New England’s 1,300 MW of wind is in Maine. But the resources can’t fully access the markets because of insufficient transmission. So Stephen Conant, senior vice president of Anbaric Transmission, said that he was mystified when officials running a clean energy solicitation for Connecticut, Rhode Island and Massachusetts included no transmission projects in their shortlist of projects last October.

Anbaric had proposed a project to unlock Maine’s bottleneck and another project to deliver New York wind power and Canadian hydropower into Vermont. (See New England States Move Toward Renewables Contracts.)

NECA renewable energy conference
Berwick | © RTO Insider

“There’s all kinds of theories out there,” Conant said during a panel on the role of transmission and energy storage in integrating renewables, when asked to explain why his and other transmission projects were shut out. “We’re all sort of scratching our heads.”

Also in that session, Dan Berwick, general manager of the energy storage division at Borrego Solar Systems, said he was not dismayed by the limitations of current battery technology, which remains expensive for many large-scale, long-term storage applications.

“I’m pretty convinced we don’t need a technological breakthrough right now — that the reductions in cost and the improvement in quality and performance that we’re going to see through increasing repetitions and scale is capable of delivering a four- or five-fold decrease in … cost.”

– Rich Heidorn Jr.

PJM Fuel-Cost Policy Changes to Take Effect in May

By Rory D. Sweeney

VALLEY FORGE, Pa. — PJM expects to implement its new fuel-cost policy rules on May 15, PJM’s Jeff Schmitt told the Market Implementation Committee last week. That would require generators to file any policy changes by March 15 to guarantee approval before the transition date.

PJM fuel-cost policy
Schmitt | © RTO Insider

Despite its looming implementation, the new rules continue to raise substantial questioning from stakeholders, which PJM is attempting to address with a FAQ document.

On Feb. 3, FERC largely accepted PJM’s proposed rule changes, siding with the RTO in requiring that policies be verifiable and systematic but not algorithmic, as Monitoring Analytics, the Independent Market Monitor, had proposed. (See FERC Seeks More Details on PJM Fuel-Cost Policy Proposal.)

The Monitor said the policies should be based on a simple average of broker quotes, bilateral offers or a weighted average index price posted on the Intercontinental Exchange (ICE) trading platform. The commission said the Monitor’s insistence that policies be “algorithmic under all circumstances” ignores how natural gas markets operate during stressed conditions that may make them illiquid, potentially understating generators’ real costs.

The Monitor contends the term “algorithmic” is misunderstood by PJM and by FERC. Algorithmic simply means a step-by-step process to get from a defined input to an output; it is therefore virtually impossible to have a verifiable policy that is not also algorithmic, it says.

Schmitt, the manager of market analysis, said PJM’s verification documents the steps taken daily to develop cost-based offers that do not change based on variables. He walked through the documents necessary for an approved policy, including filing a numerical example for each cost-based offer, likely on a spreadsheet, in the Monitor’s Member Information Reporting Application. While generators’ decisions won’t be challenged during the policy review, it’s critical for them to note whether they include emissions and variable operations and maintenance in their offers, he said. The Monitor has required a numerical example for all approved fuel-cost policies for more than two years.

Stakeholders expressed concern that the rules for dual-fuel generators appeared to not allow the flexibility to switch between fuels as desired, essentially requiring a forced outage. PJM and the Monitor said that the preferred resolution would be to create a cost-based offer for each fuel type.

PJM fuel-cost policy
Mooney | © RTO Insider

FERC made “a pretty strong statement” on the separate fuel-type offers, and that “flies in the face of only needing one cost-based offer for dual-fuel units,” said Catherine Tyler Mooney of Monitoring Analytics.

“If we commit you on a gas schedule, and you run on oil, that risk exposure is 100% yours,” said Adam Keech, PJM executive director of market operations. “Our intention is not to put you on a forced outage when you have fuel.”

As long as a generator has an approved cost-based offer, “we think [it] should be able to switch as needed based on physical requirements,” Monitor Joe Bowring said.

PJM and the Monitor also addressed ongoing questions about their relationship in approving policies. The sides appeared to have settled their differences, as the tone of their comments were markedly less confrontational than they had been at recent meetings. (See Stakeholders Caught in PJM-IMM Dispute over Fuel-Cost Policy.)

“Once we’ve been through reviewing the policies, it makes it easier for PJM,” Bowring said. “I can’t think of one we’ve approved that PJM hasn’t approved. … It’s proven efficient to go through us first.”

PJM fuel-cost policy
Greiner | ©  RTO Insider

“It’s been helpful for PJM folks to be in listening mode during the IMM negotiations,” said Stu Bresler, PJM senior vice president of operations and markets.

However, the Monitor’s late submittal of proposed revisions in Manual 15 regarding its role in the policy-review process created some heartburn among stakeholders. Before the agenda had even been discussed at the beginning of the meeting, Gary Greiner, director of PJM market policy at Public Service Enterprise Group, questioned why the Monitor had been allowed to file such a late addition. Bowring responded that when his group must respond to late filings, it becomes impossible to avoid filing them late himself.

Mooney explained that the Monitor’s proposed changes would enunciate the separation between it and PJM in the approval process.

PJM fuel-cost policy
O’Connell | © RTO Insider

“Working together is happening, but it should be clear that the reviews are separate,” she said.

Bob O’Connell of Panda Power Funds questioned why the Monitor elected to propose that it “may” provide its recommendation regarding policy approval to PJM in writing. He requested that it be changed to “shall.”

“Not having that recommendation in writing is troublesome,” he said.

Bowring responded that the Monitor plans to provide its recommendations in writing and that it is always very clear with market participants about issues with fuel-cost policies.

MISO Market Subcommittee Briefs

CARMEL, Ind. — MISO will make two changes to improve its year-old emergency pricing structure by this summer in addition to the two emergency pricing floors rolled out last year, RTO staff said during a March 9 Market Subcommittee meeting.

The first change: Commitment costs of offline fast-start units will be allocated into the minimum runtime when calculating the offer floor for emergency prices.

day-ahead margin assurance payment miso market subcommittee
Akinbode | © RTO Insider

The second: Emergency-committed units dispatched at their economic minimum prices will be allowed to set those emergency prices.

The two changes were the only selected among the five proposed by MISO staff after a July 2016 emergency event resulted in depressed prices. (See “MISO May Tweak Emergency Pricing Floors,” MISO Market Subcommittee Briefs.)

MISO engineer Oluwaseyi Akinbode said the modifications are meant to produce more efficient prices.

“If you believe what the planners are saying, there’s a chance we will get into these emergency conditions this summer, and we want to be prepared for that,” Akinbode said.

New User Group Aims to Improve Ease-of-Use in MISO Apps

MISO will later this month debut a new Application User Group for people who use the RTO’s technology.

April Peterson, a representative from MISO’s asset registration team, said the group will focus on improvements and common challenges market participants face when using the RTO’s computer market applications. She said attendance is also open to MISO software vendors and IT specialists that are contracted to make software changes.

Peterson said MISO aims to hold conference calls monthly, with the first call scheduled for March 23.

Potential Cost Recovery Gap in Manual Redispatch

Day-ahead resources can see gaps in cost recovery when they are manually redispatched offline — and a Tariff change could remedy the problem, MISO staff said.

When the RTO decommits a day-ahead resource, the day-ahead margin assurance payment does not take into account the resource’s minimum down times or start-up costs for reimbursement, said Jason Howard, MISO market quality manager.

Howard said yet-to-be-written Tariff language could “close the gap.”

“The manual redispatch might only last four hours, but a minimum down time for a resource might be seven hours,” Howard explained. “Our current day-ahead margin assurance payment does not account for these situations.”

Proposed Tariff language will be presented at a future Market Subcommittee meeting.

— Amanda Durish Cook

IMAPP Pondering 4 Options for Incorporating Clean Energy in NE

By Rich Heidorn Jr.

AUBURNDALE, Mass. — Stakeholders are considering four proposals for making New England’s markets more accommodating to state clean-energy initiatives, including a carbon adder in the energy market, potential changes to the capacity market and a possible new “clean energy” market.

ISO-NE IMAPP clean energy
Doot | © RTO Insider

David T. Doot, counsel and secretary to the New England Power Pool, outlined the changes to about 200 attendees at the Northeast Energy and Commerce Association’s 2017 Renewable Energy Conference on March 6.

Doot said the four long-term proposals were narrowed from the 17 proposed over seven meetings of the Integrating Markets and Public Policy (IMAPP) initiative last year. Officials announced last month that IMAPP will suspend its monthly meetings until May to allow ISO-NE time to develop “a conceptual market approach” that could be implemented in the near term for “accommodate[ing] state-supported capacity resources while appropriately pricing other resources in the Forward Capacity Market.” The delay also will allow states time to analyze long-term proposals discussed to date and for them to hold “off-line” discussions with stakeholders. (See NEPOOL Extends IMAPP Timeline.)

“We at the moment are in a pause … because ISO-NE has said, ‘We have to give you something to deal with the here-and-now that we’re worried about,” Doot explained. “They’re going to come back with something for us to debate and digest in the May timeframe.”

Infancy or Unruly Teens?

ISO-NE IMAPP clean energy
O’Connor | © RTO Insider

Panel moderator David O’Connor, senior vice president for energy and clean technology at ML Strategies, set up the panel by describing IMAPP as a “work in progress,” adding that “by various metrics it could be described as yet being in its infancy.”

But Doot characterized the initiative as being in “the unruly teen years.”

“We’re well beyond our infancy at this point. … We get into this room [and] there’s a lot of people talking to each other, by each other, at each other — in varying levels of decibels depending on what exactly is going on.”

Proactive

Doot said it was essential that New England stakeholders be proactive in developing a solution, noting that FERC has two cases pending before it challenging zero-emission credits for nuclear generators in NYISO and PJM.

“If we — NEPOOL or New England — don’t do something, FERC is going to do it. They will do something to us or for us. And I can predict with some degree of certainty that we won’t like it,” Doot said.

ISO-NE IMAPP clean energy
Gerwatowski | © RTO Insider

“So I think what we need to do is decide whether we’re going to take the opportunity in New England to establish how we want to change the marketplace in order to help the states achieve what they’re trying to achieve in a way that allows the rest of the market to function, or whether we’re going to have FERC tell us how they’re going to do it. Because what we currently have is not necessarily sustainable in the long term.”

Ron Gerwatowski, an energy and regulatory policy consultant, formerly with National Grid, agreed on the need to eliminate what he called the current “market schizophrenia.”

“Somebody’s going to take a meat ax to this if we don’t fix it on our own,” he said.

Four Proposals Explained

Doot said the proposed carbon adder would be included in energy offers and energy clearing prices and collected from carbon emitters under an allocation to be determined.

A second alternative, proposed by the Conservation Law Foundation, calls for a “Carbon-Integrated” Forward Capacity Market (FCM-C), under which a new ZEC market would be integrated with the FCM.

A third option, offered by RENEW Northeast and NextEra Energy, is a Forward Clean Energy Market (FCEM), a new forward market for new clean energy resources. As initially proposed, the FCEM would expand to include supports for existing renewable resources.

“We’ve been moving a little bit away from that in part because the price tag is so high,” Doot said. “What they’re now talking about is a capacity clean energy market just for new [resources] but that they would allow for support of existing resources through some form of carbon pricing.”

The fourth proposal is a two-tiered pricing construct, with the FCM clearing at one price for existing resources and a lower price for state-supported resources offered at below competitive prices, an effort to protect prices from being suppressed.

‘Civil War’

Gerwatowski said one challenge is that the states are not unified in their goals, referring to “somewhat of a civil war” between the northern and southern states.

ISO-NE IMAPP clean energy
Left to right: O’Connor, Norman, Doot, Krich, Kearns and Gerwatowski | © RTO Insider

“We have some uniformity among Connecticut, Rhode Island and Massachusetts … with respect to the very aggressive goals to reduce greenhouse gas emissions. We’re in a very different place, I think, in New Hampshire and Maine — and in Vermont it’s hard to read with the new administration coming in,” Gerwatowski said, referring to Republican Gov. Phil Scott, who replaced Democrat Peter Shumlin in January.

“If you’re in the southern states, anything that’s going to drive greenhouse gas reduction, even if it comes at some costs, is going to be something that should be under consideration,” he said, referring to carbon pricing and long-term contracts for renewables.

“They have a different perspective in the north. … They’re not quite as convinced that these are the right ways to go in designing the future. We’ve heard some of the states, like New Hampshire in particular, saying, ‘Look, you guys want to do something to raise prices in order to meet your goals, that’s OK. But I’m not paying for it.’”

Capacity Market Limitations

ISO-NE IMAPP clean energy
Krich | © RTO Insider

Abigail Krich, president of Boreas Renewables, said that while New England’s capacity market has provided price signals to encourage development of natural gas generators, it is insufficient for resources such as wind. Boreas worked on the FCEM proposal as a consultant to RENEW Northeast.

A combined cycle plant that wins a seven-year capacity contract at $7/kW-month can lock in almost 60% of its overnight capital costs, and a simple cycle turbine with the same contract would lock in 70% of its capital costs — both percentages high enough to secure financing, she said.

“A wind project, even if it’s actually more cost effective overall when you look at energy, capacity, [renewable energy credits], things like that … they can only lock in about 6% of their capital costs,” she said. “You can’t take 6% of your capital costs as locked-in revenues and go get financing for a project based on that.”

That, she said, is why long-term power purchase agreements are being sought for renewables. “We need these to be financeable projects,” she said.

ISO-NE IMAPP clean energy
Norman | © RTO Insider

Jon Norman, vice president of government and regulatory affairs for Brookfield Renewable, said the current capacity market was designed primarily to support conventional fossil generation and doesn’t address a growing gap in value recognition for existing sources of non-emitting generation, including hydropower and wind projects with expiring PPAs.

“At some point there needs to be a stable price signal” for existing clean resources, he said. “In the absence of that, you … end up over the long run cycling capital through and just putting it into new resources. And then old resources are either exporting somewhere else or they’re retiring. I don’t think that’s a good outcome.”

ISO-NE IMAPP clean energy
Kearns | © RTO Insider

Matt Kearns, chief development officer for Longroad Energy Partners, said that states have generally found long-term contracts the cheapest way to meet their renewable portfolio standards.

“We’ve seen the most consumer savings generated by these larger procurements. … The result has been to attract cheap capital and drive down the cost of the product to the consumer,” he said. “Sending a signal to the market for a 15-year contract, you tend to get very competitive, good results.”

What Would FERC Do?

Doot said that he has been asked whether FERC has the authority to approve market rules that incorporate carbon policy. The commission has scheduled a technical conference for May 1-2 on the energy and capacity markets in PJM, NYISO and ISO-NE.

Before President Trump’s election, Doot said, FERC was “begging us to come forward with something under our voluntary market structure that they can consider and potentially say yes to. Now, that was FERC before President Trump.”

After Trump? “There’s just no way of predicting,” Doot said.

Doot ended the session by returning to a question about how consumer advocates can ensure that ratepayers don’t “double pay” for carbon reductions through both an ISO-NE-wide carbon price and state initiatives such as renewable portfolio standards.

“The answer is ‘Show up.’ Because at the end of the day we have to come up with a solution. … If we don’t come up with a solution, I’m not sure you have an assurance that you aren’t double paying.

“It’s up to us — the marketplace — to help define how it is we’re going to address these challenges. If we don’t, the federal government and the state governments are going to do it, and I’m not sure that the marketplace is going to be happy with the outcome.”

MISO Contemplates Market Design Changes from FERC Offer Cap Rule

By Amanda Durish Cook

CARMEL, Ind. — MISO is considering how to alter its market rules to comply with a FERC order that “softens” the current energy offer cap and establishes a higher “hard” cap for cost-based offers.

One potential change: The RTO could possibly increase its maximum value of lost load (VoLL), which represents the estimated amount that firm electricity customers would be willing to pay to avoid losing service. The VoLL, established in 2005, caps LMPs at $3,500/MWh. MISO is the only RTO to enforce such a cap.

FERC MISO offer cap market design
Hansen | © RTO Insider

“We really should update the value of lost load,” Chuck Hansen, MISO senior market engineer, said during a March 9 Market Subcommittee meeting. “It’s been around for a decade. It’s probably time to refresh that number.”

Hansen said MISO is hoping to implement FERC’s directive by winter 2017/18, although the scope of the market changes could vary from adjusting the VoLL to ending LMP caps altogether.

Order 831 replaces the current energy offer cap of $1,000/MWh with a soft cap of $1,000 and a hard cap of $2,000 for verified cost-based incremental offers. MISO’s offer portal will be reprogrammed to automatically block all offers above $2,000/MWh, while offers between $1,000 and $2,000/MWh will be verified only after the daily market close.

A resource may qualify for uplift payments if legitimate offers above $1,000/MWh cannot be verified quickly enough. For the past three winters, FERC has granted MISO a waiver on the RTO’s energy offer cap policy. (See MISO Granted Winter Waiver on Offer Cap.)

“We have not seen offers above $1,000 yet in MISO,” said Jeff Bladen, MISO executive director of market design. “The degree to which we could see them is just too hard to predict, [but] the likelihood that we see offers above $1,000 or $2,000 — [in] my view is it’s pretty unlikely because we haven’t seen it before.”

Hansen said MISO’s Independent Market Monitor will adapt to the new offer cap by stepping up its monitoring efforts next winter, updating resource reference levels as it keeps tabs on natural gas prices throughout the day. Going forward, market participants will be able to request a consultation with the Monitor for higher reference levels. The Monitor’s Jason Fogarty said it would host a workshop later this year for market participants on the consultation process.

| MISO

The Monitor’s 2017 State of the Market report will likely recommend that MISO update the VoLL cap to also reflect the “likelihood of real-time capacity loss exceeding a given reserve level,” Fogarty said.

According to Hansen, the higher energy offer cap paired with the operating reserve demand curve during scarcity conditions could easily breach the $3,500/MWh threshold.

Hansen said MISO could try to weather the higher energy cap with an updated VoLL cap and minimal Tariff changes — or undertake a major market redesign, in which the LMP cap would be abandoned in favor of a PJM-style system marginal price cap. MISO could also divorce its operating reserve demand curve from its VoLL cap, although it must be careful to keep LMPs in check, he said.

More involved market changes would “preclude a quick solution” — and MISO is hesitant to pursue a major market redesign, Hansen said. The RTO is asking market participants to submit suggestions on the issue by March 20.

PAR Wars: A Struggle for Power

By Rory D. Sweeney

A few months ago in an ISO not that far away…

Unrest grows along the PJM-NYISO border after the dismantling of the CON ED-PSEG WHEEL that for decades held sway over daily operations in the region. Expensive infrastructure replacements loom on the horizon, and stakeholders on both sides suspect the other of attempting to take advantage of the situation.

At the RAMAPO SUBSTATION, a phase angle regulator has failed, sparking a dispute between territorial transmission owners that threatens to reignite longstanding, deep-seated grudges.

As a last resort, a small group of delegates from both sides of the border have journeyed to an unassuming office complex on the outskirts of PHILADELPHIA to meet in person in the hope of averting chaos…

VALLEY FORGE, Pa. If Friday’s joint PJMNYISO meeting to discuss replacing a phase angle regulator (PAR) at Consolidated Edison’s Ramapo substation, near the New York-New Jersey border, had a “Star Wars”-like preamble crawling off into space, it would probably look something like that. Ok, maybe a bit less dramatic.

One of the substation’s two PARs failed in June, and Con Ed has hesitated to replace it until it receives certainty on how it will be paid for. That has been in question because the 1993 agreement signed by NYISO (then known as the New York Power Pool) and PJM transmission owners is in dispute.

The agreement covered just the original PARs at the facility, PJM transmission owners argue, neither of which remains in service. They say Con Ed’s decision in 2013 to replace the first failed PAR constituted a breach of the agreement, which requires the PJM transmission owners to be involved in the decision. Con Ed disagrees with that interpretation and believes the cost allocations under the contract — which would put PJM transmission owners who were a party to the agreement on the hook for 50% of the costs — remain in effect. However, stakeholders said that Con Ed’s reluctance to replace the failed equipment without knowing how it will be repaid doesn’t square with the company’s argument for why it replaced the first PAR after its failure in 2013, without consulting transmission owners.

“It seems like your own decision not to replace the PAR is in violation of your own interpretation of the agreement,” said Mark Younger of Hudson Energy Economics.

But before deciding on who should pay for it, some stakeholders are asking whether it needs to be replaced in the first place. In its current form, Calpine can’t support the project’s scope, company representative David “Scarp” Scarpignato said. “You really need to know what projects should be shared before you discuss sharing those costs,” he said. “The cost of paying for the PAR is not the big deal here. It’s that you’re potentially using the PAR to change the winners and losers here.”

PJM NYISO phase angle regulator
Dave Scarpignato, Calpine (foreground) and Adam Keech, PJM | © RTO Insider

He argued that the PAR helps alleviate congestion, which mutes the price signals on which generation companies like Calpine depend. “When you’re talking about using transmission to manage congestion rather than dispatching to address congestion, that is direct competition to generation,” he said.

Since the 1970s, operator and planners have operated under an agreement in which Con Ed wheels 1,000 MW of power through Public Service Electric and Gas’ transmission system in northern New Jersey into New York City. Con Ed announced last year that it no longer needs the service and would be canceling it as of May 1. Con Ed also canceled its membership in PJM and ended all commitments for cost allocation in the RTO, despite having been the reason for a substantial amount of now-unnecessary transmission upgrades. PJM stakeholders have taken issue with being forced to take on additional financial responsibility for maintaining infrastructure that’s no longer in use or being paid for by its intended beneficiary. (See NYISO Members OK End to Con Ed-PSEG Wheel.)

PSE&G’s Vilna Gaston asked if there had been an analysis regarding the benefits of replacing the PAR to determine if that’s even the best investment. “It seems like we’re proposing a solution before we do the investigation. This is putting the cart before the horse,” she said.

PJM NYISO phase angle regulator
| PJM

Despite their disagreements, stakeholders produced a list of objectives for a potential analysis, including ensuring the endorsed solution adheres to competitive market principles and that the cost allocation is aligned with who receives the benefits.

PARs are an expensive solution. Beyond the millions of dollars in installation costs, PARs require about $200,000/month in upkeep, PJM’s Stan Williams said. Additionally, NYISO allocates such costs through all of its load-serving entities, while in PJM, only the signatories to the original agreement would share the costs, so there is a larger group to distribute through in NYISO than in PJM.

The group’s next meeting will be on April 18 at NYISO’s offices.

[Editor’s Note: An earlier version of this article incorrectly reported that the phase angle regulators on the 5018 line at the Ramapo substation were part of the CON ED-PSEG wheeling service. The Ramapo PARs were not part of the wheel.]